Thesises

 

    - M.S. in Material Science (Ceramic Technology) (1997)

                    "Fabrication of Al2O3–TiC Composite Material by Hot Isostatic Pressing (HIP)"

    

     - Dr.Eng. in Materials Science and Engineering (Particulate Engineering) (2003)

                     "Advanced Preparation of Hard Composite Materials with Mechanically Coated Particles"

                                                       

(uncompleted)

 

 

Publications

 

[1] Suwanprateeb J., S. Tiemprateeb, S. Kangwantrakool, and Hemachadra, K.

    “The role of filler volume fraction in the strain rate dependence of calcium carbonate reinforced polyethylene,”        Journal of Applied Polymer Science, 70, 1717-1724 (1998).

 

[2] Kangwantrakool S., “Ceramic Cutting Tools: Part I,”

    Journal of National Metal and Materials Technology (MTEC), 16, 20-23 (1999)..

 

[3] Kangwantrakool S., “Ceramic Cutting Tools: Part II,”

    Journal of National Metal and Materials Technology (MTEC), 17, 60-64 (1999).

 

[4] Kangwantrakool S. and Shinohara K.

    "Preparation of New WC-Co/TiC-Al2O3 Composite Materials with Mechanically Coated Particles"

    Journal of Chemical Engineering of Japan, 34 (12) 1486-1492 (2001).

 

[5] Kangwantrakool S. and K. Shinohara; “New design of microstructure of WC-Co/TiC-Al2O3 composite materials by mechanical coating of particles,” J. Jpn. Soc. Powder and Powder Metall., In press (2002)

 

[6] Kangwantrakool S. and K. Shinohara; “Hot hardness of WC-Co/TiC-Al2O3 composite materials,” J. Chem. Eng. Japan., 35, 893-899 (2002)

 

[7] Kangwantrakool S., B. Golman and K. Shinohara; “Quantitative characterization of microstructure of WC-Co/TiC-Al2O3 composite materials with relate to mechanical properties,” J. Chem. Eng. Japan., In press (2002)

 

[8] Kangwantrakool S. and K. Shinohara; “Sintering Behavior of Mechanically Coated

      WC-Co/TiC-Al2O3 Particles by High-speed Rotational Impact Blending,”

       Submitted to Int. J. of Refr. Metals Hard Mater. (2003)

 

 

Conference Paper

 

[1] Kangwantrakool S. and Shinohara K.

    "Advanced Preparation of WC-Co/Al2O3-TiC Surface Composite Particles for Sintered Materials"

    1st Asian Particle Technology Symposium (APT 2000), December 13-15, 2000,

    Bangkok, Thailand, CD-ROM, pp. S-II (2)-3#0076.

 

[2] Kangwantrakool S. and Shinohara K.

    "Proper Composition of Coated Particles for New Cemented Carbide Materials"

    34th Autumn Meeting of the Society of Chemical Engineering of Japan (SCEJ),

    September 28-30, 2001, Sapporo, Japan, CD-ROM, pp.R109.

   

[3] Kangwantrakool S. and K. Shinohara; “Microstructure of WC-Co/TiC-Al2O3 Composite Materials Prepared from Coated Particles by Rotational Impact Blending,” Proc. Spring Meeting of the of Powder Technology Society of Japan, Kyoto, p.106 (2002)

                                 

Home